LabPowerTools
首页 标准解析库 GB/T45906.5-2025
产品标准 AI 结构化解析
GB/T45906.5-2025 变电站二次系统 第5部分:保护控制及相关设备 Substation secondary system—Part 5: Protection and control system with their equipment's requirements
发布日期 2025-08-01
实施日期 2026-02-01
替代标准 —
解析引擎 v3.4
适用范围 本文件规定了变电站二次系统继电保护及安全自动相关设备、自动化设备、电能计量及电能质量设备、采集执行设备、通信设备及辅助监控设备的技术要求。本文件适用于变电站的保护控制及相关设备的设计、研制、试验、建设、运行、维护和检修。
72 参数限值 0 试验方法 0 计算公式 2 术语 58 约束 6 引用 来源:国家标准全文公开系统
解析版本
AI 问答 术语 限值速查 限值判定 试验方法 计算公式 约束条件 引用标准 能力表述 质检复核
电力波分复用设备3.1
一种基于密集波分复用技术的光传输设备。注:主要用于承载电网生产业务。
采集执行单元3.2
一种具有合并单元和智能终端功能的设备。与一次设备采用电缆或光纤连接,对来自一次设备的模拟信号、数字信号及状态信号进行采集处理,并通过SV及GOOSE方式上送,响应对一次设备的控制命令并通过硬接点方式出口,执行对一次设备(如:互感器、断路器、刀闸、主变压器等)的测量、控制等功能的物理单元。
环境温度范围
工作场所环境(使用场所)
≥ -5 ℃ (使用场所 C1 下限)
≤ 45 ℃ (使用场所 C1 上限)
≥ -25 ℃ (室内 C1 下限)
≤ 55 ℃ (室内 C1 上限)
≥ -40 ℃ (遮蔽场所 C2 下限)
≤ 70 ℃ (遮蔽场所 C2 上限)
℃表1
环境温度最大变化率
工作场所环境(使用场所)
≤ 20 ℃/h (使用场所 C1)
≤ 20 ℃/h (室内 C1)
≤ 20 ℃/h (遮蔽场所 C2)
℃/h表1
相对湿度
工作场所环境(使用场所)
≥ 5 % (使用场所 C1 下限)
≤ 95 % (使用场所 C1 上限)
≥ 5 % (室内 C1 下限)
≤ 100 % (室内 C1 上限)
≥ 5 % (遮蔽场所 C2 下限)
≤ 100 % (遮蔽场所 C2 上限)
%表1
最大绝对湿度
工作场所环境(使用场所)
≤ 28 g/m³ (使用场所 C1)
≤ 28 g/m³ (室内 C1)
≤ 28 g/m³ (遮蔽场所 C2)
g/m³表1
大气压力(海拔不超过1000m)
工作场所
≥ 86 kPa (工作场所海拔不超过1000m 下限)
≤ 106 kPa (工作场所海拔不超过1000m 上限)
kPa5.1.1.2
大气压力(海拔不超过3000m)
工作场所
≥ 70 kPa (工作场所海拔不超过3000m 下限)
≤ 106 kPa (工作场所海拔不超过3000m 上限)
kPa5.1.1.2
水平加速度(抗震动能力)
装置
≤ 0.3 g (水平方向)g5.1.1.3
垂直加速度(抗震动能力)
装置
≤ 0.15 g (垂直方向)g5.1.1.3
贮存环境温度
装置贮存
≥ -25 ℃ (贮存 下限)
≤ 55 ℃ (贮存 上限)
℃5.1.2
贮存相对湿度
装置贮存
≤ 85 % (贮存)%5.1.2
运输环境温度
装置运输
≥ -25 ℃ (运输 下限)
≤ 70 ℃ (运输 上限)
℃5.1.2
运输相对湿度
装置运输
≤ 85 % (运输)%5.1.2
电压测量误差
测控装置
≤ 0.2 % (额定频率,电压输入0~1.2倍额定值)%7.1.3.1
电流测量误差
测控装置
≤ 0.2 % (电流输入0~2倍额定值)%7.1.3.1
有功、无功测量误差
测控装置
≤ 0.5 % (额定频率)%7.1.3.1
频率测量误差
测控装置
≤ 0.005 Hz (45Hz~55Hz)Hz7.1.3.1
直流量采集误差
测控装置
≤ 0.2 % (直流采集)%7.1.3.2
SOE分辨率
测控装置
≤ 1 ms (遥信容量100%同时动作)ms7.1.3.3
遥控动作正确率
测控装置
≥ 100 % (遥控动作)%7.1.3.4
对时误差
测控装置
< 1 ms (对时)ms7.1.3.5
间隔层设备到管理单元的事件报告传输时间
录波及分析设备
≤ 5 s (间隔层设备到管理单元)s6.2.3.4
管理单元日志条目数
录波及分析设备
≥ 10000 条 (运行日志、操作日志、维护日志各条目数)条6.2.3.5
二次设备运维管理主站接入数
录波及分析设备
≥ 5 个 (信息上送主站数量)个6.2.3.3
CPU平均负荷率(正常运行)
数据通信网关机
≤ 50 % (初始化结束后正常运行时任意5min内平均值)%7.2.3.2
CPU平均负荷率(电力系统故障雪崩)
数据通信网关机
≤ 70 % (电力系统故障(雪崩)时10s内平均值)%7.2.3.2
站控层网络通信状态变化反应时间
数据通信网关机
≤ 1 min (站控层网络通信状态变化)min7.2.3.3
单网口同时建立主站通信链接数(DL/T634.5104)
数据通信网关机
≥ 32 个 (使用DL/T634.5104通信协议)个7.2.3.4
同时建立客户端连接数(GB/T45906.3)
数据通信网关机
≥ 16 个 (与主站采用GB/T45906.3通信)个7.2.3.5
每主站缓存SOE条数(DL/T634.5104)
数据通信网关机
≥ 8000 条 (使用DL/T634.5104通信协议)条7.2.3.6
24h守时误差
数据通信网关机
≤ 1 s (无外部时钟源校正时24h)s7.2.3.7
整机功耗
数据通信网关机
≤ 70 W (整机)W7.2.3.8
千/百兆自适应网口数量
数据通信网关机
≥ 8 个 (整机配置)个7.2.3.9
交换机吞吐量
交换机
≥ (流控关闭时,不小于端口速率×端口数量)7.3.3.1
交换机端口转发速率
交换机
= (满负荷下,应等于端口速率)7.3.3.2
交换机平均转发延时
交换机
< 10 μsμs7.3.3.3
时延抖动最大值
交换机
< 1 μs (接收到相邻两帧延时变化)μs7.3.3.4
帧丢失率
交换机
= 0 (端口线速转发时)7.3.3.5
不堵塞端口的帧丢失率
交换机
= 0 (避免产生队头阻塞)7.3.3.6
SNTP对时的时间同步准确度
交换机
< 10 msms7.3.3.7
脉冲信号准时沿上升时间
时钟同步装置
≤ 100 nsns7.4.3.1
脉冲信号上升沿的时间准确度
时钟同步装置
< 1 μsμs7.4.3.1
IRIG-B(DC)码上升沿的时间准确度
时钟同步装置
< 1 μsμs7.4.3.2
IRIG-B码抖动时间
时钟同步装置
≤ 200 nsns7.4.3.2
串行口时间报文对时准确度
时钟同步装置
< 5 msms7.4.3.3
NTP/SNTP网络对时报文对时准确度
时钟同步装置
< 10 msms7.4.3.4
守时12h状态下的时间准确度
时钟同步装置
< 1 μs/h (守时12h状态)μs/h7.4.3.5
测量准确度
DL/T280 · 同步相量测量装置
= (应符合DL/T280的规定)7.5.3.1
连续录波记录采样率
同步相量测量装置
≥ 1000 HzHz7.5.3.2
连续录波记录保存时间
同步相量测量装置
≥ 3 dd7.5.3.2
低频振荡频率监视范围
同步相量测量装置
范围 (0.1Hz~2.5Hz)Hz7.5.3.3
次/超同步振荡频率监视范围
同步相量测量装置
范围 (2.5Hz~45Hz和55Hz~95Hz)Hz7.5.3.4
动态数据时标与数据输出时刻的时间差
同步相量测量装置
≤ 300 ms (100帧/s传输速率)ms7.5.3.5
装置对时误差
同步相量测量装置
≤ 1 μs (±1μs)μs7.5.3.6
失去同步时钟信号60min以内相位测量误差改变量
同步相量测量装置
≤ 1 ° (失去同步时钟信号60min以内(即时间改变量应不大于55μs))°7.5.3.6
转发实时动态数据的延迟时间
相量数据集中器
≤ 200 msms7.6.3.1a
能接入的主站个数
相量数据集中器
≥ 8 个个7.6.3.1b
能接入的PMU装置台数
相量数据集中器
≥ 8 台台7.6.3.1c
可接入的间隔数
相量数据集中器
≥ 48 个个7.6.3.1c
通信端口个数
相量数据集中器
≥ 6 个个7.6.3.1d
动态数据最高记录速率
相量数据集中器
≥ 100 次/s次/s7.6.3.2a
动态数据保存时间
相量数据集中器
≥ 14 dd7.6.3.2b
电能质量设备准确度
GB/T19862 · 电能质量设备
= (应符合GB/T19862规定的A级要求)8.3.2.2
用于直连的端口采样值发送间隔离散值
采集执行设备
≤ 10 μs (用于直连的端口)μs9.3.1.1
采样值总延时
采集执行设备
≤ 1 msms9.3.1.2
带级联功能的采样响应延时
采集执行设备
≤ 2 ms (带级联功能的采集执行设备)ms9.3.1.2
对时精度
采集执行设备
< 1 μs (采样相关)μs9.3.1.4
失去同步时钟信号10min以内的守时误差
采集执行设备
< 4 μs (失去同步时钟信号10min以内)μs9.3.1.4
跳闸、合闸继电器接点出口动作时间
采集执行设备
≤ 7 ms (从接收到保护跳闸、合闸GOOSE命令到出口)ms9.3.2.1
开入变位到GOOSE信号发出时间延时
采集执行设备
≤ 5 ms (不含防抖时间)ms9.3.2.2
事件分辨率
采集执行设备
≤ 1 msms9.3.2.3
对时精度
采集执行设备
≤ 1 ms (操作相关)ms9.3.2.4
电力波分复用设备单机传输时延
电力波分复用设备
< 1 μsμs10.3.4
检测结果限值判定(演示)
检测项目
测定结果
判定逻辑:测定结果与限值直接比对(未含测量不确定度保护带),正式报告请按 ILAC-G8 / 标准原文复核。
就这本标准问我
回答基于本标准的结构化解析与条款文本检索生成,附条款溯源;AI 解读请以标准正式原文为准。
看完方法,直接落成原始记录:自动带出检测要求与质控核查项,录读数自动计算判定,可导出活公式 Excel
本标准为限量/产品类标准,未单独抽取试验方法。
公式已就位——生成原始记录后,这些公式将变成 Excel 里的活公式,改读数自动重算重判
未抽取到计算公式。
标准中"施加在执行过程与条件上的要求"(C1 环境 / C4 样品 / C6 质控 / C7 条件限值 / C8 适用范围 / C9 过程参数),是原始记录模板与自动核查的数据源。
C1 · 环境条件强制设备内部 · 凝露/结冰
设备内部既不应凝露,也不应结冰。设备运行环境出处:28
C1 · 环境条件工作场所大气压力 · 大气压力
86 ~ 106 kPa工作场所海拔不超过1000m出处:2
C1 · 环境条件工作场所大气压力 · 大气压力
70 ~ 106 kPa工作场所海拔不超过3000m出处:2
C1 · 环境条件贮存环境 · 温度/相对湿度
-25 ~ 55 ℃贮存环境温度-25℃~+55℃,相对湿度不大于85%出处:2
C1 · 环境条件运输环境 · 温度/相对湿度
-25 ~ 70 ℃运输环境温度-25℃~+70℃,相对湿度不大于85%出处:2
C5 · 设备能力要求强制采样率 · 频率
≥ 1000 Hz出处:2
C5 · 设备能力要求强制动态数据时标与数据输出时刻的时间差 · 时间差
≤ 300 ms100帧/s传输速率出处:4
C5 · 设备能力要求强制装置对时误差 · 对时误差
装置对时误差应不大于±1μs出处:5
C5 · 设备能力要求强制相位测量误差改变量 · 相位测量误差改变量
≤ 1 °失去同步时钟信号60min以内出处:6
C5 · 设备能力要求转发实时动态数据的延迟时间 · 延迟时间
≤ 200 ms出处:1
C5 · 设备能力要求相量数据集中器可接入主站个数 · 主站个数
≥ 8 个出处:1
C5 · 设备能力要求相量数据集中器可接入PMU装置台数 · PMU装置台数
≥ 8 个出处:1
C5 · 设备能力要求允许相量数据集中器可接入间隔数 · 间隔数
≥ 48 个出处:1
C5 · 设备能力要求相量数据集中器通信端口个数 · 通信端口个数
≥ 6 个出处:1
C5 · 设备能力要求动态数据最高记录速率 · 记录速率
≥ 100 次/s出处:2
C5 · 设备能力要求强制直连端口采样值发送间隔离散值 · 发送间隔离散值
≤ 10 μs用于直连的端口出处:1
C5 · 设备能力要求强制采集执行设备采样值总延时 · 采样值总延时
≤ 1 ms出处:1
C5 · 设备能力要求强制对时精度 · 对时精度
≤ 1 μs出处:8
C5 · 设备能力要求强制守时误差 · 守时误差
≤ 4 μs失去同步时钟信号10min以内出处:8
C6 · 精密度/质控限强制遥控动作正确率 · 遥控动作正确率
≥ 100 %出处:3
C7 · 分级/条件限值强制电压测量误差 · 电压测量误差
≤ 0.2 %电压输入在0倍~1.2倍额定值范围内出处:1
C7 · 分级/条件限值强制电流测量误差 · 电流测量误差
≤ 0.2 %电流输入在0~2倍额定值范围内出处:1
C7 · 分级/条件限值频率测量误差 · 频率测量误差
≤ 0.01 Hz45Hz~55Hz范围内出处:1
C7 · 分级/条件限值强制CPU平均负荷率 · CPU平均负荷率
≤ 50 %通信网关机初始化结束后,正常运行时(任意5min内)平均值出处:1
C7 · 分级/条件限值强制CPU平均负荷率 · CPU平均负荷率
≤ 70 %电力系统故障(雪崩)时(10s内)平均值出处:2
C7 · 分级/条件限值强制装置 · 24h守时误差
≤ 1 s没有外部时钟源校正时出处:6
C7 · 分级/条件限值强制交换机镜像目的端口 · 帧丢失
当镜像目的端口数据速率不大于端口转发速率时,不应出现帧镜像目的端口数据速率不大于端口转发速率时出处:9
C7 · 分级/条件限值强制交换机 · 吞吐量
交换机吞吐量应不小于端口速率×端口数量(流控关闭时)流控关闭时出处:3
C7 · 分级/条件限值强制交换机端口转发速率 · 端口转发速率
在满负荷下,交换机端口转发速率应等于端口速率满负荷下出处:1
C7 · 分级/条件限值强制交换机 · 平均转发延时
≤ 10 μs出处:2
C7 · 分级/条件限值强制交换机 · 帧丢失率
≤ 0端口线速转发时出处:4
C7 · 分级/条件限值交换机不堵塞端口 · 帧丢失率
≤ 0避免产生队头阻塞出处:5
C7 · 分级/条件限值强制交换机SNTP对时 · 时间同步准确度
≤ 10 ms出处:6
C7 · 分级/条件限值强制装置输出脉冲信号准时沿 · 上升时间
≤ 100 ns出处:3
C7 · 分级/条件限值强制装置输出脉冲信号上升沿 · 时间准确度
≤ 1 μs出处:3
C7 · 分级/条件限值强制装置输出IRIG-B(DC)码上升沿 · 时间准确度
≤ 1 μs出处:1
C7 · 分级/条件限值强制装置输出IRIG-B码 · 抖动时间
≤ 200 ns出处:2
C7 · 分级/条件限值强制装置输出串行口时间报文 · 对时准确度
≤ 5 ms出处:2
C7 · 分级/条件限值强制装置输出NTP/SNTP网络对时报文 · 对时准确度
≤ 10 ms出处:3
C7 · 分级/条件限值强制装置 · 时间准确度
≤ 1 μs/h守时12h状态下出处:4
C7 · 分级/条件限值强制同一计量点计量误差 · 计量误差
同一计量点计量误差应符合准确度等级指数要求计量点数同时计量的情况下出处:3
C9 · 过程控制参数强制间隔层设备到管理单元的事件报告传输时间 · 传输时间
≤ 5 s出处:3
C9 · 过程控制参数强制管理单元日志条目数 · 日志条目数
≥ 10000 条运行日志、操作日志和维护日志各条目数出处:6
C9 · 过程控制参数信息上送主站数量 · 主站数量
≥ 5 个二次设备运维管理的通信能力出处:3
C9 · 过程控制参数强制遥控操作任务 · 同时支持的遥控操作任务数
≤ 1 个单台数据通信网关机同一时间出处:3
C9 · 过程控制参数强制站控层网络通信状态变化反应时间 · 通信状态变化反应时间
≤ 1 min出处:2
C9 · 过程控制参数强制单网口对主站通信链接数 · 同时建立的对主站通信链接数
≥ 32 个采用5104通信协议时出处:4
C9 · 过程控制参数强制客户端连接数 · 同时建立连接的客户端数
≥ 16 个采用5104通信协议时出处:5
C9 · 过程控制参数强制控制块缓存报告条数 · 缓存报告条数
控制块的缓存报告条数应不小于所引用数据集的成员数目不小于所引用数据集的成员数目出处:5
C9 · 过程控制参数强制每个主站缓存SOE条数 · 缓存SOE条数
≥ 8000 条采用5104通信协议时出处:6
C9 · 过程控制参数强制连续录波记录 · 文件形成周期
连续录波记录应每分钟形成一个文件出处:1
C9 · 过程控制参数强制保存时间 · 保存时间
≥ 3 d出处:2
C9 · 过程控制参数动态数据保存时间 · 保存时间
≥ 14 d出处:2
C9 · 过程控制参数强制双采样板采样回路 · 采样回路独立性
任一采样回路异常,不应导致另一采样回路误发数据任一采样回路异常出处:3
C9 · 过程控制参数强制从开入变位到GOOSE信号发出的时间延时 · 时间延时
≤ 5 ms不含防抖时间出处:1
C9 · 过程控制参数强制事件分辨率 · 事件分辨率
≤ 1 ms出处:2
C9 · 过程控制参数强制对时精度 · 对时精度
≤ 1 ms出处:3
C9 · 过程控制参数强制电力波分复用设备单机传输时延 · 单机传输时延
≤ 1 μs出处:3
GB/T9361计算机场地安全要求最新版适用规范性引用
GB/T11287—2000电气继电器 第21部分:量度继电器和保护装置的振动、冲击、碰撞和地震版本绑定规范性引用
GB/T13729远动终端设备最新版适用规范性引用
GB/T14285继电保护和安全自动装置技术规程最新版适用规范性引用
GB/T14537—1993量度继电器和保护装置的冲击与碰撞试验版本绑定规范性引用
GB/T14598.最新版适用规范性引用
检测能力(产品/限量标准)认可领域:04 电气 › 0418 通信设备
序号检测对象项目/参数领域代码检测标准(方法)名称及编号(含年号)说明备注
序号名称
1变电站二次系统1环境温度范围041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 表1
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
22环境温度最大变化率041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 表1
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
33相对湿度041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 表1
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
44最大绝对湿度041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 表1
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
55大气压力(海拔不超过1000m)041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 5.1.1.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
66大气压力(海拔不超过3000m)041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 5.1.1.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
77水平加速度(抗震动能力)041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 5.1.1.3
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
88垂直加速度(抗震动能力)041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 5.1.1.3
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
99贮存环境温度041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 5.1.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
1010贮存相对湿度041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 5.1.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
1111运输环境温度041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 5.1.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
1212运输相对湿度041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 5.1.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
1313电压测量误差041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.1.3.1
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
1414电流测量误差041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.1.3.1
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
1515有功、无功测量误差041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.1.3.1
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
1616频率测量误差041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.1.3.1
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
1717直流量采集误差041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.1.3.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
1818SOE分辨率041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.1.3.3
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
1919遥控动作正确率041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.1.3.4
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
2020对时误差041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.1.3.5
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
2121间隔层设备到管理单元的事件报告传输时间041801《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 6.2.3.4
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
2222管理单元日志条目数041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 6.2.3.5
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
2323二次设备运维管理主站接入数041801《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 6.2.3.3
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
2424CPU平均负荷率(正常运行)041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.2.3.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
2525CPU平均负荷率(电力系统故障雪崩)041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.2.3.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
2626站控层网络通信状态变化反应时间041801《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.2.3.3
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
2727单网口同时建立主站通信链接数(DL/T634.5104)041801《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.2.3.4
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
2828同时建立客户端连接数(GB/T45906.3)041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.2.3.5
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
2929每主站缓存SOE条数(DL/T634.5104)041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.2.3.6
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
303024h守时误差041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.2.3.7
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
3131整机功耗041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.2.3.8
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
3232千/百兆自适应网口数量041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.2.3.9
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
3333交换机吞吐量041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.3.3.1
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
3434交换机端口转发速率041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.3.3.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
3535交换机平均转发延时041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.3.3.3
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
3636时延抖动最大值041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.3.3.4
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
3737帧丢失率041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.3.3.5
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
3838不堵塞端口的帧丢失率041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.3.3.6
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
3939SNTP对时的时间同步准确度041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.3.3.7
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
4040脉冲信号准时沿上升时间041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.4.3.1
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
4141脉冲信号上升沿的时间准确度041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.4.3.1
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
4242IRIG-B(DC)码上升沿的时间准确度041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.4.3.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
4343IRIG-B码抖动时间041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.4.3.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
4444串行口时间报文对时准确度041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.4.3.3
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
4545NTP/SNTP网络对时报文对时准确度041803《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.4.3.4
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
4646守时12h状态下的时间准确度041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.4.3.5
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
4747测量准确度041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.5.3.1
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
引用方法:DL/T280
4848连续录波记录采样率041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.5.3.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
4949连续录波记录保存时间041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.5.3.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
5050低频振荡频率监视范围041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.5.3.3
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
5151次/超同步振荡频率监视范围041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.5.3.4
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
5252动态数据时标与数据输出时刻的时间差041804《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.5.3.5
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
5353装置对时误差041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.5.3.6
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
5454失去同步时钟信号60min以内相位测量误差改变量041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.5.3.6
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
5555转发实时动态数据的延迟时间041804《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.6.3.1a
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
5656能接入的主站个数041802《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.6.3.1b
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
5757能接入的PMU装置台数041802《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.6.3.1c
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
5858可接入的间隔数041802《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.6.3.1c
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
5959通信端口个数041801《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.6.3.1d
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
6060动态数据最高记录速率041804《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.6.3.2a
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
6161动态数据保存时间041804《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 7.6.3.2b
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
6262电能质量设备准确度041801《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 8.3.2.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
引用方法:GB/T19862
6363用于直连的端口采样值发送间隔离散值041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 9.3.1.1
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
6464采样值总延时041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 9.3.1.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
6565带级联功能的采样响应延时041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 9.3.1.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
6666对时精度041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 9.3.1.4、9.3.2.4
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
6767失去同步时钟信号10min以内的守时误差041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 9.3.1.4
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
6868跳闸、合闸继电器接点出口动作时间041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 9.3.2.1
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
6969开入变位到GOOSE信号发出时间延时041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 9.3.2.2
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
7070事件分辨率041899《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 9.3.2.3
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
7171电力波分复用设备单机传输时延041801《变电站二次系统 第5部分:保护控制及相关设备》GB/T45906.5-2025 10.3.4
Substation secondary system—Part 5: Protection and control system with their equipment's requirements
共 71 项参数:0 项已自动推荐领域代码,71 项待人工确认。领域代码依据 CNAS-AL06:2024 规则推荐,检测对象依据:标准名称(产品);正式申报前请人工核对,「说明」列的限制范围(只测/不测、量程等)按实验室实际填写。
解析模型与复核模型对以下关键数值意见不一。 点击您认可的一侧卡片即可投票,多数人的意见即最终结论;每项仅可投一次,首次投票 +2 LP。 已定案项目会在正文对应位置标注 ⚖,悬停可见两模型的分歧详情。
复核项加载中…
本页内容由 AI 从标准公开文本自动解析生成,条款级溯源("出处"列)。仅供学习参考,检测判定请以标准正式原文为准。
LabPowerTools · 超级标准
© 2026 LabPowerTools